Click here for product information pb rohs_mat rohs_comp  msds

Flat Cable EMI Suppression Cores (2643167751)

Part Number: 2643167751
43 SPLIT FLAT CABLE CORE
43 Material®
Suppression Components
Cable Component
Printer Friendly Data Sheet
Check Stock

Part Number: 2643167751

43 SPLIT FLAT CABLE CORE

Explanation of Part Numbers:
– Digits 1 & 2 = Product Class
– Digits 3 & 4 = Material Grade

Flat cable suppression core can accommodate multi-conductors flat cables, in widths from 12.7 mm (0.500) up to 77 mm (3.0). These flat cable cores are available in two ferrite material grades to reduce conducted EMI from 1 MHz to hundreds of MHz.

Clip Part Number: 0199001401 , 0199016051

Our  Expanded Cable & Suppressor Kit (part number 0199000005) contains a selection of these flat cable cores and clips.

Flat Cable Cores are available in selected sizes in the Flex Circuit & Ribbon Cable Core Kit (part number 0199000038).

Assembly clips are available for most of the split flat cable cores. See section Flat Cable Cores Assembly clips.

Catalog Drawing
3D Model

Weight: 27 (g)

Dimmmmm tolnominal inchinch misc.
A76.2±1.503_
B65.3±1.302.57_
C12.7±0.400.5_
D6.35±0.250.25_
E0.85±0.200.033_
Cable Information
Max DiameterMax DimensionSolid EquivalentFlat Cable Cores
0
0
64.00 x 1.30_-

Chart Legend
+ Test frequency
•For assembly clips see Flat Cable Cores Assembly Clips

Typical Impedance (Ω)
10 MHz23
25 MHz+43
100 MHz+110
250 MHz185

Flat cable suppression cores, split or single cores, are controlled for impedances only. Minimum impedance values are specified for the + marked frequencies. The minimum impedance is typically the listed impedance less 20%.

Catalog Drawing

Centered, single turn impedance tests for the 31 and 43 material parts are performed on the E4990A Impedance Analyzer. All tests are made with the shortest practical wire length.

Typical Impendance (Ω)
10 MHz 22
25 MHz+ 45
100 MHz+ 115
250 MHz 240

CSV Download

This NiZn is our most popular ferrite for suppression of conducted EMI from 20 MHz to 250 MHz. This material is also used for inductive applications such as high frequency common-mode chokes.

Available in 43 material®:
EMI Suppression Beads
Beads On Leads
SM beads
Multi-Aperture Cores
Round Cable EMI Suppression Cores
Round Cable Snap-Its
Flat Cable EMI Suppression Cores
Flat Cable Snap-Its
Miscellaneous Suppression Cores
Bobbins
Toroids

43 Material® Characteristics
Property Unit Symbol Value
Initial Permeability@ B < 10 gauss µi 800
Flux Density @ Field Strength Gauss
Oersted
B
H
3500
10
Residual Flux Density Gauss Br 2200
Coercive Force Oersted Hc 0.36
Loss Factor @ Frequency 10 -6
MHz
Tan δ/ µi 100
1.0
Temperature Coefficient of Initial Permeability (20 -70°C) %/°C 1.25
Curie Temperature °C Tc >130
Resistivity ohm-cm ρ 1×105

**** Characteristic curves are measured on standard Toroids (18/10/6 mm)  at 25°C and 10 kHz unless otherwise indicated. Impedance characteristics are measured on standard shield beads (3.5/1.3/6.0 mm) unless otherwise indicated.

Material Safety Data Sheet (MSDS)

Click here to download Complex Permeability vs. Frequency (CSV)

Ferrite Material Constants

Specific Heat
0.25 cal/g/°C
Thermal Conductivity
3.5 - 4.5 mW/cm-°C
Coefficient of Linear Expansion
8 - 10x10-6/°C
Tensile Strength
4.9 kgf/mm2
Compressive Strength
42 kgf/mm2
Young's Modulus
15x103 kgf/mm2
Hardness (Knoop)
650
Specific Gravity
≈4.7 g/cm3
The above quoted properties are typical for Fair-Rite MnZn and NiZn ferrites.


Storage and Operating Temperature
Printer Friendly Data Sheet - Download as pdf file

Go to Top