Wound Beads (2961666634)
61 WOUND BEAD
61 Material™
Suppression Components
Board Component
Printer Friendly Data Sheet
Check Stock
Part Number: 2961666634
61 WOUND BEAD
Explanation of Part Numbers:
– Digits 1 & 2 = Product Class
– Digits 3 & 4 = Material Grade
– Last digit 1 = Bulk Packed 4 = Taped and Reeled
Six and eleven hole beads, in two NiZn materials, are available both as beads (product class 26) and wound with tinned copper wire in several winding configurations (product class 29).
Wire used for winding is oxygen free high conductivity copper with 100% matte tin plating over a nickel undercoating.
Recommended storage temperature and operating temperature is -55 °C to 125 °C
Packaging Options:
– Parts with a 1 as the last digit of the part number are supplied bulk packed. Wound beads with part numbers 29–666631 and 29–666651 can be supplied radially taped and reeled per IEC 60286-1 and EIA 468-B standards. For these taped and reeled wound beads the last digit of the part number is a 4. Taped and reeled wound beads are supplied 500 pieces on a 13 reel.
For any wound bead requirement not listed in here, please contact our customer service group for availability and pricing.
Weight: 1.4 (g)
Dim | mm | mm tol | nominal inch | inch misc. |
A | 6 | ±0.25 | 0.236 | _ |
B | 0.75 | +0.15 | 0.032 | _ |
C | 10 | ±0.25 | 0.394 | _ |
D | 3.51 | Ref | 0.138 | Ref |
Winding Information | |||
Turns Tests | Wire Size | 1st Wire Length | 2nd Wire Length |
3 | 0.53 24 AWG | 38.0 ±3.0 (1.500”) | _ |
Reel Information | ||||
Tape Width mm | Pitch mm | Parts 7" Reel | Parts 13" Reel | Parts 14" Reel |
_ | 12.7 | _ | 500 | _ |
Chart Legend
+ Test frequency
•A ½ turn is defined as a single pass through a hole.
Typical Impedance (Ω) | |
10 MHz | 245 |
50 MHz+ | 830 |
100 MHz+ | 1130 |
200 MHz+ | 1200 |
400 MHz | 645 |
Beads are controlled for impedance limits only. Minimum impedance values are specified for the + marked frequencies. The minimum impedance is typically the listed impedance less 20%.
The 44 material beads and wound beads are tested on the E4990A Impedance Meter. The 61 material parts on the E4991A / HP4291B Impedance Analyzer.
Typical Impendance (Ω) | |
10 MHz | 175 |
50 MHz+ | 700 |
100 MHz+ | 1000 |
200 MHz+ | 1100 |
400 MHz | 625 |
A high frequency NiZn ferrite developed for a range of inductive applications up to 25 MHz. This material is also used in EMI applications for suppression of noise frequencies above 200 MHz. Excellent stability characteristics.
Strong magnetic fields or excessive mechanical stresses may result in irreversible changes in permeability and losses.
Available in 61 material™:
EMI Suppression Beads
Beads On Leads
SM beads
Wound Beads
Multi-Aperture Cores
Round Cable Snap-Its
Toroids
Rods
Antenna/RFID
Rods
Round EMI Suppression Cores
61 Material™ Characteristics
Property | Unit | Symbol | Value |
Initial Permeability @ B < 10 gauss | µi | 125 | |
Flux Density @ Field Strength | Gauss Oersted |
B H |
2500 15 |
Residual Flux Density | Gauss | Br | 1000 |
Coercive Force | Oersted | Hc | 1.2 |
Loss Factor @ Frequency | 10 -6 MHz |
Tan δ/ µi | 90 10 |
Temperature Coefficient of Initial Permeability (20 -70°C) | %/°C | .10 | |
Curie Temperature | °C | Tc | >300 |
Resistivity | ohm-cm | ρ | 1×108 |
**** Characteristic curves are measured on standard Toroids (18/10/6 mm) at 25°C and 10 kHz unless otherwise indicated. Impedance characteristics are measured on standard shield beads (3.5/1.3/6.0 mm) unless otherwise indicated.
Material Safety Data Sheet (MSDS)
Click here to download Complex Permeability vs. Frequency (CSV)
Click here to download 61 Material Power Loss Density vs. Flux Density at 25°C
Ferrite Material Constants
Storage and Operating Temperature
Printer Friendly Data Sheet - Download as pdf file